2. configuration & dimensions : superworld electronics (s) pte ltd pg. 1 (f) (d) (e) (b) (c) (a) 1. part no. expression : unit:m/m (g) sps5020ft series 3. materials : (a) core : ferrite (c) wire : polyurethane enamelled copper wire (d) solder : m35e (e) coating : powder coating 2.0 max. a b c 2.0 typ. de 1.1 typ. 5.0 0.2 5.0 0.2 (c) powder coating type (a) series code (b) dimension code (f) tolerance code : m = 20%, n = 30% (d) taping package (e) inductance code : 1r0= 1.0uh (g) 11~99 : internal controlled number (e) ink : 70000-00101 f 4.1 typ. (b) copper foil : c5191 s p s 5 0 2 0 f t 1 r 0 n - ?? 20.03.2012 low profile power inductors note : specifications subject to change without notice. please check our website for latest information. 1r0 a b c e d e f marking (black) powder coating 4.3 1.6 2.0 1.6 standard pattern
5. electrical characteristics : 4. general specification : c) rated dc current: the less value which is idc1 or idc2. b) idc2 : based on temperature rise ( ? t: 40c typ.) a) idc1 : based on inductance change ( ? l/lo: -30%) @ ambient temp. 25c e) storage temperature range ...... -40c ~ +105c d) operate temperature range ...... -40c ~ +105c (including self temp. rise) superworld electronics (s) pte ltd pg. 2 sps5020ft1r2n inductance 3.330% ( uh ) idc1 (
) 0.1v/1m 25m 5.0 ( a ) rdc idc2 3.90 ( a ) ( hz ) frequency test 20% sps5020ftr47n 0.4730% 0.1v/1m 15m 7.0 5.10 sws part no. sps5020ft1r5n 1.530% 30m 4.5 3.30 0.1v/1m sps5020ft1r0n 1.030% 25m 5.5 3.90 0.1v/1m sps5020ft2r2n 2.230% 42m 3.6 2.80 0.1v/1m sps5020ft3r3n 3.330% 61m 3.2 2.50 0.1v/1m sps5020ft3r9n 3.930% 74m 3.2 2.30 0.1v/1m 20.03.2012 low profile power inductors note : specifications subject to change without notice. please check our website for latest information. marking 1r2 r47 1r5 1r0 2r2 3r3 3r9 sps5020ft series sps5020ft4r7m 4.720% 84m 2.9 2.10 0.1v/1m 4r7 sps5020ft6r8m 6.820% 0.10 2.3 1.70 0.1v/1m 6r8 sps5020ft100m 1020% 0.14 1.8 1.45 0.1v/1m 100 SPS5020FT150M 1520% 0.22 1.5 1.10 0.1v/1m 150 sps5020ft220m 2220% 0.32 1.3 0.87 0.1v/1m 220 sps5020ft330m 3320% 0.50 1.0 0.65 0.1v/1m 330
superworld electronics (s) pte ltd 6. reliability & test condition : resistance to soldering heat vibration substrate bending item (a total of 6 hours) the condition shown in the above profile for 1 time. 130~150c and after it has been immersed to a depth 0.5mm with new solder smoothly when the sample is taken out of the specimen shall be stored at standard atmospheric conditions for 1 hour, after which the measurement shall there shall be no damage or problems. the specimen shall be passed through the reflow oven with the solder bath. more than 90% of the electrode sections shall be cowered a temperature of 2455c. below for 30.2 seconds fully in molten solder m705 with then be preheated for about 2 minutes in a temperature of flux (rosin, isopropyl alcohol{jis-k-1522}) shall be coated over the whole of the sample before hard, the sample shall be applied to the 3 directions (x,y,z) for 2 hours each. a frequency of from 10 to 55hz/1 minute repeated should there shall be no mechanical damage. ? l/lo 10% there shall be no mechanical damage or the sample shall be soldered onto the printed circuit board and when a vibration having an amplitude of 1.52mm and performance test condition electrical damage. the sample shall be soldered onto the printed circuit board in figure 1 and a load applied until the figure in the arrow direction is made approximately 3mm.(keep time 30 secs) pressure rod figure-1 solderability new solder more than 90% mechanical (reflow soldering) be made. 100 40 2 20 50 20 30 30 20 t = 1.6 4.5 452 452 20 10 r5 r340 bending test board ? l/lo 10% 300 250 200 150 100 50 2 min. 10 sec 2 min. or more 150~ 180c 30 sec min. (230 c ) soldering (peak temperature 2603c 10sec) slow cooling (stored at room temperature) pre-heating soldering temperature (c) +0 20.03.2012 low profile power inductors note : specifications subject to change without notice. please check our website for latest information. sps50 20 ft series
superworld electronics (s) pte ltd 6. reliability & test condition : low temperature storage temperature characteristics dielectric withstand voltage item the sample shall be left for 964 hours in an atmosphere sample has been left in a normal temperature and normal with a temperature of -253c. upon completion of the test, t he measurement shall be made humidity for 1 hour. upon completion of the measurement shall be made after the the sample shall be left for 964 hours in an atmosphere with a temperature of 852c and a normal humidity. temperature and normal humidity shall be ? l/l20c 10%. calculated based on the value applicable in a normal 0~2000 ppm/c ? l/l20c 10% the test shall be performed after the sample has stabilized in an ambient temperature of -20 to +85c,and the value performance test condition ac 100v voltage shall be applied for 1 minute across the top surface and the terminal of this sample high temperature storage electrical characteristics test after the sample has been left in a normal temperature and there shall be no damage or problems. there shall be no mechanical damage. there shall be no mechanical damage. normal humidity for 1 hour. change of temperature moisture storage there shall be no other damage of problems there shall be no mechanical damage. the sample shall be subject to 5 continuos cycles, such as shown in the table 2 below and then it shall be subjected to standard atmospheric conditions for 1 hour, after which measurement shall be made. duration 852c 4 2 3 1 (thermostat no.1) 5 sec. or less -253c temperature 30 min. no.1 : no.2 5 sec. or less no.2 : no.1 30 min. (thermostat no.2) standard atmospheric standard atmospheric the sample shall be left for 964 hours in a temperature of 402c and a humidity(rh) of 90~95%. upon completion of the test, the measurement shall be made after the sample has been left in a normal temperature and normal humidity more than 1 hour. ? l/lo 10% ? l/lo 10% ? l/lo 10% ? l/lo 10% 20.03.2012 low profile power inductors note : specifications subject to change without notice. please check our website for latest information. sps50 20 ft series
7. packaging information : superworld electronics (s) pte ltd 7-1. reel dimension (mm) 100 18 2.2 7-2 carrier tape dimensions (mm) 17.3 13.2 330 13 120 7-3 taping dimensions (mm) 12mm w 5.35mm 5.5mm 1.55mm ao ko bo t p 0.3mm 8.0mm 7-4 quantity 3000pcs/reel the products are packaged so that no damage will be sustained. t 4.00 2.000.05 ao p a a ko w 5.50 1.75 ?1.5+0.1/-0.0 1.5 bo 20.03.2012 low profile power inductors note : specifications subject to change without notice. please check our website for latest information. 8mm 4 mm start end leader no component 200mm min. components trailer no component 400mm min. user direction of feed 1r0 1r0 1r0 1r0 sps50 20 ft series
|
